Mallory-ignition Mallory MAGNETIC BREAKERLESS IGNITION MODULE 609 Instrukcja Użytkownika Pobierz pdf

INSTALLATION INSTRUCTIONS

FORM 1356 (REV. C) 2/00

MAGNETIC BREAKERLESS

IGNITION MODULE

PART NO. 609

APPLICATION: YLM and YTM Series Distributors; 50 Series Mechanical Advance Distributors; 57 Series

Vacuum Advance Distributors; 82 Series Mechanical Advance Billet Competition Distributors; COMP

9000

87 Series Vacuum Advance Distributors; COMP 9000

89 Series Mechanical Advance Distribu-

tors; Magnetic Breakerless Ignition Conversions.

Remove the Allen head screw or screws (there may

be one or two) that hold the old module assembly to

the steel plate. The old module assembly should be

loose. If the old module assembly is not loose,

remove the two magnetic pickup nuts on the old

module assembly. See Figure 1.

Series 82 and 89 Distributors

Remove the two Allen head screws that hold the old

module assembly to the steel plate. The old module

assembly should be loose. If the old module assem-

bly is not loose, remove the two magnetic pickup

nuts on the old module assembly. See Figure 1.

Step 3

Lift the old module assembly up and out of the

distributor housing.

INSTALLATION PROCEDURE

Step 1

Remove the distributor cap and rotor (NOTE: On

Series Nos. 82, 87 and 89 Distributors, also remove

the adapter shield). Unplug the old module (female

connector) from the distributor wire harness. Cut the

female connector off the end of the wires from the old

module assembly and push the wires through the

grommet. See Figure 1.

Step 2

YLM and YTM Series, and 50 Series

Distributors

Loosen (do not remove) the two nuts on the side of

the distributor housing.

Series 57 and 87 Distributors

Remove the small E-clip that holds the vacuum

advance linkage on the drive pin on the steel plate.

Lift the vacuum advance linkage off the drive pin.

FIGURE 1

1 2 3 4

Podsumowanie treści

Strona 1 - IGNITION MODULE

0®INSTALLATION INSTRUCTIONSFORM 1356 (REV. C) 2/00MAGNETIC BREAKERLESSIGNITION MODULEPART NO. 609APPLICATION: YLM and YTM Series Distributors; 50 Seri

Strona 2 - FIGURE 2

2FIGURE 3Step 4Loosen the two magnetic pickup nuts on the newmodule assembly. See Figure 2.NOTE (57, 82, 87 and 89 Series Distributors): Ifyou had to

Strona 3 - DISTRIBUTOR WIRE

2REVIEW WIRINGPROCEDUREIMPORTANT: Make sure that your vehicle isequipped with an ignition ballast resistor (or loomresistance wire) in the wire betwe

Strona 4 - FIGURE 5

4MALLORY IS A DIVISION OF THE MR. GASKET PERFORMANCE GROUP550 MALLORY WAY, CARSON CITY, NV 89701(775) 882-6600 FAX (775) 887-4326www.mrgasket.comFORM

Komentarze do niniejszej Instrukcji

Brak uwag

Mallory-ignition Mallory MAGNETIC BREAKERLESS IGNITION MODULE 609 Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Do samochodu Mallory-ignition Mallory MAGNETIC BREAKERLESS IGNITION MODULE 609. Mallory Ignition Mallory MAGNETIC BREAKERLESS IGNITION MODULE 609 User Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Do samochodu Mallory-ignition Mallory MAGNETIC BREAKERLESS IGNITION MODULE 609